Figure 1 Figure 2 Figure 3
Figure 4 Figure 5 Figure 6
Figure 7 Figure 8 Figure 9
Installation Instructions:
Attaching Wall Mount to Studs:
Locate a proper place to mount by using a quality stud finder 1.
(Figure 1). Mark center of stud. It is recommended that the
center of the stud be used and that a nail be used to verify that
a stud has been located.
Gently pull back vinyl cover at top of backplate to expose 2.
plate. Hold mount up to wall and mark wall at top of mount
backplate at desired height. (Figure 2) (Set mount aside after
marking)
Measure down stud from top of plate 2-5/8” and mark for first 3.
screw. (Figure 3) and drill (3/16” x 3”) deep pilot hole into wall
at mark
Using Hex Key (Provided) screw (1) Hex Screw into pilot hole 4.
leaving 1/8” gap to wall.
Carefully cut cable tie holding motorized plate. (Figure 9)5.
Place mount on screw using butterfly hole (second hole from 6.
top).
Level mount using Bubble Level and drill 2nd (3/16” x 3”) deep 7.
pilot hole through bottom hole in backplate. (Figure 7)
Using Hex Key attach 2nd screw/washer combination (Do Not 8.
Overtighten) (Figure 7)
Drill 3rd (3/16” x 3”) deep pilot hole through hole through top 9.
hole in backplate. (Figure 8)
Attach 3rd screw/washer combination (Do Not Overtighten) 10.
(Figure 8)
Using Hex Key tighten first screw (Do Not Overtighten)11.
Attaching Wall Mount to Concrete:
Gently pull back vinyl cover at top of backplate to expose 1.
plate. Hold mount up to wall and mark wall at top of mount
backplate at desired height. (Figure 2) (Set mount aside after
marking)
Measure down from top of plate 2-5/8” and mark for first screw. 2.
(Figure 3)
Drill (1/2” x 3-1/8”) deep hole into wall at mark (Figure 4)3.
Insert Concrete Anchor flush with wall. (Figure 5)4.
Using Hex Key (Provided) screw (1) Hex Screw into concrete 5.
anchor leaving 1/8” gap to wall. (Figure 6)
Place mount on screw using butterfly hole (second hole from 6.
top).
Level mount using Bubble Level mark two remaining mounting 7.
holes on wall.
Remove mount and drill at marks (1/2” x 3-1/4”) deep holes.8.
Insert concrete anchors until flush with wall.9.
Carefully cut cable tie holding motorized plate. (Figure 9)10.
Reinstall mount on single screw. 11.
Attach 2nd and 3rd screw/washer combination (Do Not 12.
Overtighten)
Using Hex Key tighten first screw (Do Not Overtighten)13.
Top of Mount
Top of Mount
Bottom of Mount
S
T
S
T
Top of Mount Mark
2-5/8”
Please Refer to Stud Finder
Instruction Manual
U
Attaching LCD/Plasma to Mounting Arms:
Determine Correct bolt to attach TV to Mounting Arm.1.
Caution: Carefully thread the bolt into the back
of your LCD to determine which bolt is to be used. If
there is any resistance remove the bolt immediately.
Select longest bolt that can be fully threaded into TV.
Never place LCD/Plasma screen face
down on any surface to prevent scratching.
DO NOT OVERTIGHTEN BOLTS WHEN INSTALLING ARMS
ON TELEVISION.
Install mounting arm to TV with Bolt, Lock Washer, and Flat 2.
Washer for M4 or M5 Bolts. (Figure 10)
Install mounting arm to TV with Bolt and Lock Washer3. for M6
or M8 Bolts. (Figure 11)
Figure 10
M4 and M5 Bolts
Bags 1 or 2
Figure 11
M6 and M8 Bolts
Bags 3 or 4
www.LevelMount.com
1-888-229-1459
©2008 Level Mount
Patents Pending
(USE SPACER
ONLY IF
NEEDED)
(USE SPACER
ONLY IF
NEEDED)
(22 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals